Just like in the previous tutorial on MainStage 3, I’ll show you how to use the minimum amount of equipment (only one footswitch and one pedal) to set andcontrol any number of effects in Overloud TH‑U (stand‑alone version).
First, however, I’ll go over a very simple standard approach to show its limitations.
Approach 1
Available on http://www.marcofanton.it/th-u-patches.html. Free Preset Pack for Overloud's TH-U Based on Famous Song Tones. Seasoned guitarist Ruben Reza returns with a special preset pack for Overloud's guitar amp and FX suite TH-U. Ruben is no stranger to tone. A self-described 'tone-freak', he's been known to spend hours upon hours tweaking knobs until he gets the sound he's after.
Suppose you only have the overdrive and wah‑wah effects on your pedalboard. You want to turn each one on and off using the footswitch and control the wah‑wah effect with the pedal.
As for hardware, you need one regular expression pedal, one double footswitch, and one USB MIDI adapter or the autonomous MIDI pedals EX3 and FS3.
Once you have your MIDI foot controllers ready, open “Audio Settings”, and make sure it is active:
In TH‑U, just as in its predecessor TH‑3, there are two possibilities to assign MIDI messages to effects – only for a given Preset and globally (for all Presets). The procedure of assigning is the same – right click on the effect and select the appropriate option:
You can also assign one message to control a given type of effect (and not its specific model), i.e. CC #1 will control each wah‑wah pedal, whether it’s Rox (Vox)or Cry Maybe (Cry Baby), or any new model. To do this, open the MIDI menu and click “Learn” in the corresponding section, in this case “Wah”:
Proceed in the same way by assigning and mapping both footswitch buttons to toggle the wah‑wah and overdrive effects on and off.
Overloud Th3 Free
Approach 2
Cinemagraph online. Add the whammy pedal to the Approach 1 configuration. We also want to turn it on and off and control it using the pedal. In the standard approach described above, we would have to buy a second expression pedal, a second footswitch, and an additional MIDI adapter.
To avoid this and use only the equipment we have, we can apply one simple trick - switch between entire Programs. Cleanmymac x 4 4 3 cr2 converter. A Program, i.e. a Preset, is a whole group of effects and their settings.
After adding the whammy effect to the Preset, copy and paste it into the empty slot.
Proceed in the same way as in Approach 1, assigning the expression pedal to different effects in each Preset - wah‑wah or whammy, while setting one of them on and the other off:
Preset
wah‑wah
whammy
1
on
off
2
off
on
Overloud Th-u Presets
In addition, you can copy these Preset again, and in each Preset set whether overdrive is enabled or not:
Preset
wah‑wah
whammy
overdrive
1
on
off
on
2
off
on
on
3
on
off
off
4
off
on
off
And now the most important part – how to switch between Presets. There are 2 ways in TH‑U. The simplest way: in the MIDI settings, check “Program Changes recall presets in current bank”: (I described the “Program Change” message in more detail here)
In the application for configuring the MIDI controller, set the Toggle mode to “Up/Down Program #”.
The second way is a bit less intuitive, because the MIDI specification uses messages such as Program Change to switch presets, but some controllers do not have this functionality. In such case, you can use CC event by assigning the corresponding controller numbers to call the functions “Next preset” and “Previous preset”:
This way, having only two buttons physically available, we can switch between the entire presets, not just turn individual effects on and off.
Overloud Amp
In the next blog posts, I will describe how to configure other Amp Sims. Stay tuned.